Bionaire Electric Heater BCH6151 CN User Manual

BCH6151-CN_08EFM2.qxd :127671 5/26/08 4:45 PM Page 1  
REMOTE CONTROL INSTRUCTIONS  
Before operation, insert 2 “AAA” batteries (not included)  
into the back of the remote control.  
14.To prevent a possible fire, DO NOT block air intakes or  
exhaust in any manner. DO NOT use on soft surfaces,  
like a bed, where openings may become blocked.  
15.To disconnect heater, turn controls to OFF, then remove  
plug from outlet.  
16.Avoid the use of an extension cord because the  
extension cord may overheat and cause a risk of fire.  
However, if you have to use an extension cord, the  
cord shall be No. 14 AWG minimum size and rated not  
less than 1875 watts.  
17.If the heater will not operate, see specific instructions  
on Auto Safety Shut-off.  
18.DO NOT attempt to repair or adjust any electrical or  
mechanical functions on this unit. Doing so will void  
your warranty. The inside of the unit contains no user  
serviceable parts. All servicing should be performed by  
qualified personnel only.  
19.Discontinue use if plug or outlet is hot. It is  
recommended that the outlet be replaced if plug or  
outlet is hot to touch.  
a potential overheat temperature is reached, the system  
will automatically shut the heater off. It can only resume  
operation when the user resets the unit. For specific reset  
instructions please refer to the unit.  
off, but still plugged in to an AC outlet, only the room  
temperature will be visible.  
3. When not in “Auto” mode, only the room temperature  
will be displayed from 30-99 Fahrenheit or 0-39  
Celsius.  
4. When the heater is in “Auto” mode and the heating  
element has been turned off after reaching the set  
temperature, the fan will continue to run for 25  
seconds.  
HEATER SAFETY  
PLEASE READ AND SAVE  
THESE IMPORTANT SAFETY  
INSTRUCTIONS  
Fig 2  
Digital Triple  
Ceramic  
Heater  
To Reset the Heater:  
1. Unplug the heater and wait 30 minutes for the unit to  
cool down.  
2. After the 30 minutes, plug the unit in again and operate  
normally.  
Temp Up  
Button  
Mode/On  
Button  
When using electrical appliances, basic safety  
precautions should always be followed to reduce the risk  
of fire, electric shock, and injury to persons, including the  
following:  
Temp Down  
Button  
Timer Button  
Auto Shut Off Programmable Timer Instructions:  
MODEL BCH6151-CN  
Tip Over Shut-Off:  
1. Read all instructions before using the appliance.  
2. To avoid fire or shock hazard, plug the appliance  
directly into a 120V AC electrical outlet.  
1. While your heater is in the ON mode, press the Timer  
Button ( ) and the numbers will start flashing on the  
right of the display. pressing the ( ) or ( ) buttons  
to go from 0-24 to set the number of hours you want  
your heater to run before shutting off.  
2. Two seconds after releasing the Timer Button ( ), the  
LCD will return to the previous setting and a small clock  
will appear to indicate the timer is set.  
Oscillation  
Button  
If the unit is tipped over in any direction, it will instantly  
shut off. To reset, simply place the heater in an upright  
position and it will operate normally.  
3. The heater is hot when in use. To avoid burns, DO NOT  
let bare skin touch hot surfaces. If provided, use  
handles when moving this heater. Keep combustible  
materials, such as furniture, pillows, bedding, papers,  
clothes, and curtains at least 3 ft (0.9 m) from the front  
of the heater and keep them away from the sides and  
rear.  
4. DO NOT run cord under carpeting. DO NOT cover cord  
with throw rugs, runners, or the like. Arrange cord away  
from traffic area and where it will not be tripped over.  
5. This heater is not intended for use in bathrooms,  
laundry areas and similar indoor location. NEVER locate  
heater where it may fall into a bathtub or other water  
container.  
6. Extreme caution is necessary when any heater is used  
by, or near children or invalids, and whenever the  
heater is left operating and unattended.  
7. Always unplug the heater when not in use.  
8. When unplugging, be sure to pull by the plug and not  
the cord.  
9. DO NOT insert or allow foreign objects to enter any  
ventilation or exhaust opening as this may cause an  
electric shock or fire, or damage the heater.  
10.DO NOT operate heater with a damaged cord or plug,  
or after the heater malfunctions, has been dropped or  
damaged in any manner. Return appliance to  
manufacturer for examination, electrical or mechanical  
adjustment, or repair.  
• Do not mix old and new batteries.  
• Do not mix alkaline, standard (carbon-zinc), or  
rechargeable (nickel-cadmium) batteries.  
The remote control for this unit has the capability of  
operating all control panel functions. Please note this  
remote control will not work through walls.  
POWER: To turn the unit on press the Mode/On Button.  
To turn the unit off press the Mode/On Button and scroll  
to OFF.  
MODES: To scroll through the various modes LO, HI, AL  
and AH press the Mode/On Button until you reach your  
desired setting.  
OSCILLATION: To start oscillation, press the Oscillation  
Button ( ) once. To stop oscillation press the Oscillation  
Button ( ) again.  
TEMPERATURE: To increase the temperature setting,  
press the Temp Up Button ( ). To decrease the  
temperature setting that you desire press the Temp Down  
Button ( ).  
Timer: To activate the timer from the remote control,  
press the button marked Timer. From there you can  
press the Temp Up ( ) or Temp Down ( ) Button,  
which will give you the ability to program the heater to  
turn on or off in 1 hour increments, up to 24 hours. For  
more information see the programmable timer  
instructions above.  
PRE-OPERATING INSTRUCTIONS  
1. Carefully remove your heater from the box. Please save  
the carton for off-season storage.  
2. Make sure the unit is in the OFF position before  
plugging the heater into the outlet.  
3. Place heater on firm level surface.  
4. Avoid overloading your circuit by not using other high  
wattage appliances in the same outlet. At 1500 Watts,  
this unit draws 12.5 Amps.  
3. If the Timer Button ( ) is pressed while the heater is  
running, the time remaining is shown and can be  
changed by pressing the ( ) or ( ) buttons.  
PLEASE SAVE THESE  
INSTRUCTIONS  
4. You can turn off the timer by pressing the Timer Button  
(
) back to zero, let the heater run to the end of the  
programmed period or by turning the heater OFF using  
the Mode Button ( ).  
CONSUMER SAFETY INFORMATION  
NOTE: The power light will illuminate when the heater is  
THIS APPLIANCE HAS A POLARIZED  
AC PLUG (one blade is wider than the  
other). To reduce the risk of electric  
turned on.  
Auto On Programmable Timer Instructions:  
1. When your heater is OFF, press the Timer Set button  
and the numbers will start flashing on the right of the  
display. Press the ( ) or ( ) buttons to go from 0-24  
to set the number of hours that you want your heater to  
turn On.  
2. At the specified time, the heater will turn on to an  
automatic setting of Auto High at 75 Fahrenheit or 24  
Celsius. and will remain on for 2 hours.  
DIGITAL THERMOSTAT  
Your heater is equipped with a Digital Thermostat that allows  
you to set your heater to your precise comfort level.  
shock, this plug is intended to fit in a  
polarized outlet only one way. If the plug  
does not fit fully in the outlet, reverse the  
plug. If it still does not fit, contact a  
Mode Instructions:  
qualified electrician to install the proper outlet.  
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH  
Fig 1  
Oscillation  
Button  
WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.  
3. When the heater turns On, the power light will appear  
and a small clock will appear on the display to signal  
the timer is activated.  
DO NOT ATTEMPT TO MODIFY THIS PLUG OR  
DEFEAT THIS SAFETY FEATURE IN ANY WAY.  
Mode  
Button  
Temp/Timer  
Up Button  
4. You can turn off the timer by pressing the Timer Button  
PLEASE READ AND SAVE  
THESE IMPORTANT SAFETY  
INSTRUCTIONS  
TECHNICAL SPECIFICATIONS  
• Wattage: 1500W (+5% -10%)  
• Working voltage: 120V AC/60Hz  
Timer  
Button  
(
) back to zero, let the heater run to the end of the  
Temp/Timer  
Down Button  
programmed period or by pressing the Mode Button  
) before the timer runs out.  
(
Read instructions before operating.  
Retain for future reference.  
CLEANING/MAINTENANCE  
11.A heater has hot and arcing or sparking parts inside.  
DO NOT use it in areas where gasoline, paint, or  
flammable liquids are used or stored.  
12.Use appliance only for intended household use as  
described in this manual. Any other use not  
recommended by the manufacturer may cause fire,  
electric shock, or injury to persons. The use of  
attachments not recommended or sold by the  
manufacturer may cause hazards.  
Remote Sensor Led  
OSCILLATION INSTRUCTIONS  
During Season Care:  
1. Always unplug the heater before cleaning.  
2. Clean the unit with a soft cloth moistened with a mild  
soap solution.  
3. NEVER use abrasive or flammable solvents to clean the  
unit.  
1. Select the desired temperature and mode settings and  
Instruction Leaflet  
1. Press the Mode Button ( ) to turn heater On and it  
will automatically set to High. Press ( ) to select Low  
setting. Press the Mode Button ( ) again for “Auto Hi”  
or “Auto Lo.”  
press the Oscillation Button ( ) to the ON position.  
2. To stop oscillation, press the Oscillation Button (  
again.  
)
INFO-LINE  
If after having read this leaflet, you have any  
AUTO SAFETY SHUT-OFF WITH INSTANT TIP  
OVER PROTECTION  
This heater is equipped with a patented, technologically-  
advanced safety system that requires the user to reset  
the heater if there is a potential overheat situation. When  
questions or comments on your heater,  
3. Please do not manually turn the heater on the base; it  
is designed to turn only by motorized oscillation.  
2. While in “Auto” mode, pressing the ( ) or (  
)
buttons will adjust the set temperature within a range of  
55-85 Fahrenheit or 13-30 Celsius. The LCD display on  
your heater will display both room and the set  
call 1-800-253-2764 in North America.  
4. After cleaning, be sure to completely dry the unit with a  
cloth or towel.  
127671/9100020009457  
13.DO NOT use outdoors.  
temperature while in “Auto” mode. When the heater is  
After Season Care:  
1. Store heater in a cool, dry location.  
1 YEAR LIMITED WARRANTY  
Sunbeam Products, Inc. doing business as Jarden  
Consumer Solutions or if in Canada, Sunbeam  
How to Obtain Warranty Service  
In the U.S.A.  
2. The manufacturer recommends that you store the unit  
in its original carton.  
*TIP: Over time, dust may accumulate on the front grills.  
This can be removed by wiping the unit with a damp  
cloth. Always unplug unit and allow to cool prior to  
cleaning.  
If you have any question regarding this warranty or would  
like to obtain warranty service, please call 1-800-253-2764  
and a convenient service center address will be provided  
to you.  
Corporation (Canada) Limited doing business as Jarden  
Consumer Solutions (collectively “JCS”) warrants that for a  
period of one year from the date of purchase, this product  
will be free from defects in material and workmanship.  
JCS, at its option, will repair or replace this product or any  
component of the product found to be defective during the  
warranty period. Replacement will be made with a new or  
remanufactured product or component. If the product is  
no longer available, replacement may be made with a  
similar product of equal or greater value. This is your  
exclusive warranty. Do NOT attempt to repair or adjust any  
electrical or mechanical functions on this product. Doing  
so will void this warranty.  
In Canada  
If you have any question regarding this warranty or would  
like to obtain warranty service, please call 1-800-253-2764  
and a convenient service center address will be provided  
to you.  
TROUBLESHOOTING  
If your heater fails to operate:  
• UNPLUG THE UNIT  
• Make sure the electrical outlet or circuit breaker is  
working.  
• Check for obstructions. If you find an obstruction turn  
the heater OFF, and unplug the unit. Carefully remove  
the obstruction and follow the reset instructions.  
• The temperature may be set too low. Adjust the  
thermostat until the heater restarts.  
In the U.S.A., this warranty is offered by Sunbeam  
Products, Inc. doing business Jarden Consumer Solutions  
located in Boca Raton, Florida 33431. In Canada, this war-  
ranty is offered by Sunbeam Corporation (Canada) Limited  
doing business as Jarden Consumer Solutions, located at  
20 B Hereford Street, Brampton, Ontario L6Y 0M1. If you  
have any other problem or claim in connection with this  
product, please write our Consumer Service Department.  
This warranty is valid for the original retail purchaser from the  
date of initial retail purchase and is not transferable. Keep  
the original sales receipt. Proof of purchase is required to  
obtain warranty performance. JCS dealers, service centers,  
or retail stores selling JCS products do not have the right to  
alter, modify or any way change the terms and conditions of  
this warranty.  
This warranty does not cover normal wear of parts or  
damage resulting from any of the following: negligent use or  
misuse of the product, use on improper voltage or current,  
use contrary to the operating instructions, disassembly, repair  
or alteration by anyone other than JCS or an authorized JCS  
service center. Further, the warranty does not cover: Acts of  
God, such as fire, flood, hurricanes and tornadoes.  
PLEASE DO NOT RETURN THIS PRODUCT TO ANY  
OF THESE ADDRESSES OR TO THE PLACE OF  
PURCHASE.  
Please DO NOT attempt to open or repair the heater.  
Please see the Warranty for Service Instructions.  
If you have any questions regarding your product or  
®
would like to learn more about other Bionaire products,  
please contact our Consumer Service Department at  
What are the limits on JCS’s Liability?  
JCS shall not be liable for any incidental or consequential  
damages caused by the breach of any express, implied or  
statutory warranty or condition.  
Except to the extent prohibited by applicable law, any  
implied warranty or condition of merchantability or fitness  
for a particular purpose is limited in duration to the dura-  
tion of the above warranty.  
JCS disclaims all other warranties, conditions or represen-  
tations, express, implied, statutory or otherwise.  
JCS shall not be liable for any damages of any kind result-  
ing from the purchase, use or misuse of, or inability to use  
the product including incidental, special, consequential or  
similar damages or loss of profits, or for any breach of  
contract, fundamental or otherwise, or for any claim  
brought against purchaser by any other party.  
Some provinces, states or jurisdictions do not allow the  
exclusion or limitation of incidental or consequential dam-  
ages or limitations on how long an implied warranty lasts,  
so the above limitations or exclusion may not apply to you.  
© 2008 Sunbeam Products, Inc. doing business as  
Jarden Consumer Solutions. All Rights Reserved.  
Distributed by Sunbeam Products, Inc. doing business as  
Jarden Consumer Solutions, Boca Raton, Florida 33431  
.
This warranty gives you specific legal rights, and you may  
also have other rights that vary from province to province,  
state to state or jurisdiction to jurisdiction.  
BCH6151CN08EFM2 Printed in China  
 

Black Box Network Card Express 8 Port Mux User Manual
Black Box Power Screwdriver Delux Optical Power Meter with Memory User Manual
Black Decker Food Processor FP1445 User Manual
Bosch Appliances Home Care Product F01U252722 User Manual
Briggs Stratton Portable Generator 206405GS User Manual
Brother All in One Printer 1820C User Manual
Bryant Furnace 315AAV User Manual
Cabletron Systems Switch CSX500 User Manual
Cecilware Griddle EL 1624 User Manual
Channel Plus Camcorder H721 User Manual