Bionaire Fan BFH6500 User Manual

BFH6500CN08EFM1.qxd:BFH6500CN08EFM1.qxd 2/1/08 4:57 PM Page 1  
14.To prevent a possible fire, DO NOT block air intakes or  
exhaust in any manner. DO NOT use on soft surfaces,  
like a bed, where openings may become blocked.  
15.To disconnect heater, turn controls to OFF, then remove  
plug from outlet.  
16.Avoid the use of an extension cord because the  
extension cord may overheat and cause a risk of fire.  
However, if you have to use an extension cord, the  
cord shall be No. 14 AWG minimum size and rated not  
less than 1875 watts.  
17.If the heater will not operate, see specific instructions  
on Auto Safety Shut-off.  
18.DO NOT attempt to repair or adjust any electrical or  
mechanical functions on this unit. Doing so will void  
your warranty. The inside of the unit contains no user  
serviceable parts. All servicing should be performed by  
qualified personnel only.  
19.DISCONTINUE USE IF PLUG OR OUTLET IS HOT. WE  
RECOMMEND OUTLET BE REPLACED IF PLUG OR  
OUTLET IS HOT TO TOUCH.  
DIGITAL THERMOSTAT  
Setting the Off Timer:  
1. Select the Mode and/or temperature you wish the  
heater to run in.  
2. While the heater is running, press and hold the up and  
down buttons simultaneously.  
3. By pressing the up and down buttons, program the  
heater to turn off in up to 16 hours from the current  
time, in increments of 1 hour.  
4. After setting the timer, the LED display will return to  
show the current room temperature. A LED will  
illuminate to show that the timer is activated.  
5. After the predetermined length of time has passed, the  
heater will automatically shut off.  
AUTO SAFETY SHUT-OFF WITH INSTANT TIP OVER  
PROTECTION  
HEATER SAFETY  
Your heater is equipped with a Digital Thermostat that  
allows you to set your heater to your precise comfort level.  
PLEASE READ AND SAVE  
THESE IMPORTANT  
SAFEGUARDS  
This heater is equipped with a patented,  
Remote Control  
Tower Fan  
Heater  
technologically-advanced safety system that requires the  
user to reset the heater if there is a potential overheat  
situation. When a potential overheat temperature is  
reached, the system will automatically shut the heater off. It  
can only resume operation when the user resets the unit.  
For specific reset instructions please refer to the unit.  
Setting the Digital Thermostat:  
1. Press the Mode Button once for manual HI power. The  
heater will run continuously on HI.  
2. Press the Mode Button again for manual LO power.  
The heater will run continuously on LO.  
3. Press the Mode Button for a third time for Auto Mode  
HI Power (AH) or press again for Auto Mode LO Power  
(AL). In either of these modes you may then press the  
up , and down buttons to preset your desired  
temperature.  
4. Once you have preset your desired temperature, the  
display will return to current room temperature and  
gradually increase until the room has reached the  
preset temperature.  
5. If the unit will not start in the digital thermostat mode,  
please make sure the “preset temperature” is higher  
than the current room temperature.  
When using electrical appliances, basic safety precautions  
should always be followed to reduce the risk of fire, electric  
shock, and injury to persons, including the following:  
MODEL BFH6500  
To Reset the Heater:  
1. Read all instructions before using the appliance.  
2. To avoid fire or shock hazard, plug the appliance directly  
into a 120 V AC electrical outlet.  
If the unit shuts down:  
1. Unplug unit.  
2. Wait 10 minutes for unit to cool down.  
3. Plug in and operate normally.  
3. The heater is hot when in use. To avoid burns, DO NOT  
let bare skin touch hot surfaces. If provided, use handles  
when moving this heater. Keep combustible materials,  
such as furniture, pillows, bedding, papers, clothes,  
and curtains at least 3 ft (0.9 m) from the front of the  
heater and keep them away from the sides and rear.  
4. DO NOT run cord under carpeting. DO NOT cover cord  
with throw rugs, runners, or the like. Arrange cord  
away from traffic area and where it will not be tripped  
over.  
5. This heater is not intended for use in bathrooms, laundry  
areas and similar indoor locations. NEVER locate  
heater where it may fall into a bathtub or other water  
container.  
6. Extreme caution is necessary when any heater is used  
by, or near children or invalids, and whenever the  
heater is left operating and unattended.  
7. Always unplug the heater when not in use.  
8. When unplugging, be sure to pull by the plug and not  
the cord.  
9. DO NOT insert or allow foreign objects to enter any  
ventilation or exhaust opening as this may cause an  
electric shock or fire, or damage the heater.  
10.DO NOT operate heater with a damaged cord or plug,  
or after the heater malfunctions, has been damaged in  
any manner. Return appliance to manufacturer for  
examination, electrical or mechanical adjustment, or  
repair.  
Setting the On Timer:  
1. While the heater is off, press and hold the up and down  
buttons simultaneously.  
2. By pressing the up and down buttons, program the  
heater to turn on up to 16 hours in advance of current  
time, in increments of 1 hour.  
3. After the preset length of time has passed, the heater  
will automatically turn on at the last mode setting that  
was programmed. If no program was set, the heater  
will turn on Auto Mode HI Power at 75°F (24°C) for a  
preset time of 2 hours.  
NOTE: After reaching the preset temperature, the unit will  
briefly continue to run with fan only. This ensures a  
consistent and accurate temperature reading.  
Tip-Over Shut-Off:  
When the unit is accidentally knocked over, it will instantly  
shut off. To reset, simply place the heater in an upright  
position. Press the MODE button and it will operate  
normally.  
PLEASE SAVE THESE  
INSTRUCTIONS  
NOTE: It is normal for the heater to cycle ON and OFF as it  
maintains the preset temperature. To prevent the unit from  
cycling, you need to raise the thermostat setting. When the  
preset temperature is reached, the fan will run for 30  
seconds without heat. This cool down process ensures an  
accurate and consistent temperature reading. If you unplug  
the heater, you will have to reset the digital thermostat  
again by following the above instructions.  
CONSUMER SAFETY INFORMATION  
OSCILLATION INSTRUCTIONS  
1. Select the desired temperature and mode settings and  
press the oscillation (osc.) button.  
2. To stop oscillation, press the oscillation button again.  
3. Please do not manually turn the heater on the base; it  
is designed to turn only by motorized oscillation.  
PRE-OPERATING INSTRUCTIONS  
THIS APPLIANCE HAS A POLARIZED  
AC PLUG (one blade is wider than the  
other). To reduce the risk of electric  
1. Carefully remove your heater from the box. Make  
certain to remove parts from both sides of the packing  
foam. Please save carton for off-season storage.  
2. Place heater on a firm level surface.  
3. Your heater comes assembled.  
4. Avoid overloading your circuit by not using other high  
wattage appliances in the same outlet. At 1500 Watts,  
this unit draws 12.5 Amps.  
shock, this plug is intended to fit in a  
polarized outlet only one way. If the plug  
does not fit fully in the outlet, reverse the  
plug. If it still does not fit, contact a  
NOTE: Digital thermostat has memory. The digital  
thermostat will remember the previous temperature setting  
after the unit has been turned off. However, if the unit is  
unplugged, the digital thermostat will be reset and will no  
longer remember the previous temperature setting.  
qualified electrician to install the proper outlet.  
DO NOT ATTEMPT TO MODIFY THIS PLUG OR  
DEFEAT THIS SAFETY FEATURE IN ANY WAY.  
NOTE: The power light will illuminate when the heater is  
turned on.  
USING THE PROGRAMMABLE TIMER  
PLEASE READ AND SAVE  
THESE IMPORTANT  
SAFETY INSTRUCTIONS  
TECHNICAL SPECIFICATIONS  
Digital thermostat allows the user to program the heater to  
turn on at a preset time, or turn off after a set amount of  
time.  
Read instructions before operating.  
Retain for future reference.  
11.A heater has hot and arcing or sparking parts inside.  
DO NOT use it in areas where gasoline, paint, or  
flammable liquids are used or stored.  
Instruction Leaflet  
INFO-LINE  
12.Use appliance only for intended household use as  
described in this manual. Any other use not  
recommended by the manufacturer may cause fire,  
electric shock, or injury to persons. The use of  
attachments not recommended or sold by the  
manufacturer may cause hazards.  
Wattage:  
Working Voltage:  
1500W (+ 5% - 15%)  
120V AC/60 Hz  
¤
If after having read this leaflet, you have any  
questions or comments on your heater,  
call 1-800-253-2764 in North America.  
13.DO NOT use outdoors.  
126965/9100020008812  
2 YEAR LIMITED WARRANTY  
REMOTE CONTROL INSTRUCTIONS  
1. Before operation, insert 2 “AAA” batteries into the back  
of the remote control.  
• Do not mix old and new batteries.  
• Do not mix alkaline, standard (carbon-zinc), or  
rechargeable (nickel-cadmium) batteries.  
CLEANING/MAINTENANCE  
During Season Care:  
This warranty gives you specific legal rights, and you may  
also have other rights that vary from province to province,  
state to state or jurisdiction to jurisdiction.  
Sunbeam Products, Inc. doing business as Jarden  
Consumer Solutions or if in Canada, Sunbeam Corporation  
(Canada) Limited doing business as Jarden Consumer  
Solutions (collectively “JCS”) warrants that for a period of  
two years from the date of purchase, this product will be  
free from defects in material and workmanship. JCS, at its  
option, will repair or replace this product or any component  
of the product found to be defective during the warranty  
period. Replacement will be made with a new or remanu-  
factured product or component. If the product is no longer  
available, replacement may be made with a similar product  
of equal or greater value. This is your exclusive warranty.  
Do NOT attempt to repair or adjust any electrical or  
mechanical functions on this product. Doing so will void  
this warranty.  
1. Always unplug the heater before cleaning.  
2. Clean the unit with a soft cloth moistened with a mild  
soap solution.  
3. NEVER use abrasive or flammable solvents to clean  
the unit.  
4. After cleaning, be sure to completely dry the unit with  
a cloth or towel.  
After Season Care:  
How to Obtain Warranty Service  
In the U.S.A.  
If you have any question regarding this warranty or would  
like to obtain warranty service, please call 1-800-253-2764  
and a convenient service center address will be provided  
to you.  
The remote control for this unit  
has the capability of operating all  
control panel functions. Please  
note this remote control will not  
work through walls.  
In Canada  
If you have any question regarding this warranty or would  
like to obtain warranty service, please call 1-800-253-2764  
and a convenient service center address will be provided  
to you.  
1. Store heater in a cool, dry location.  
POWER: To turn the unit on press  
the Mode/On Button. To turn the  
unit off press the OFF button.  
2. The manufacturer recommends that you store the unit  
in its original carton.  
In the U.S.A., this warranty is offered by Sunbeam  
Products, Inc. doing business as Jarden Consumer  
Solutions located in Boca Raton, Florida 33431. In  
Canada, this warranty is offered by Sunbeam Corporation  
(Canada) Limited doing business as Jarden Consumer  
Solutions, located at 20 B Hereford Street, Brampton,  
Ontario L6Y 0M1. If you have any other problem or claim in  
connection with this product, please write our Consumer  
Service Department.  
This warranty is valid for the original retail purchaser from  
the date of initial retail purchase and is not transferable.  
Keep the original sales receipt. Proof of purchase is  
required to obtain warranty performance. JCS dealers,  
service centers, or retail stores selling JCS products do not  
have the right to alter, modify or any way change the terms  
and conditions of this warranty.  
This warranty does not cover normal wear of parts or dam-  
age resulting from any of the following: negligent use or  
misuse of the product, use on improper voltage or  
current, use contrary to the operating instructions,  
disassembly, repair or alteration by anyone other than JCS  
or an authorized JCS service center. Further, the warranty  
does not cover: Acts of God, such as fire, flood,  
hurricanes and tornadoes.  
TIP: Over time, dust may accumulate on the front grills.  
MODES: To scroll through the  
various modes LO, HI, AL and AH  
press the Mode/On Button until  
you reach your desired setting.  
This can be removed by wiping the unit with a damp  
cloth. Always unplug unit and allow to cool prior to  
cleaning.  
OSCILLATION: To start oscillation, press the Osc. Button  
once. To stop oscillation press the button again.  
TROUBLESHOOTING  
If your heater fails to operate:  
• UNPLUG THE UNIT.  
• Make sure the electrical outlet or circuit breaker is  
working.  
• Check for obstructions. If you find an obstruction turn  
the heater OFF, and unplug the unit. Carefully remove  
the obstruction and follow the reset instructions.  
• The temperature may be set too low. Adjust the  
thermostat until the heater restarts.  
TEMPERATURE: To increase the temperature setting,  
press the Temp Up button . To decrease the temperature  
PLEASE DO NOT RETURN THIS PRODUCT TO ANY  
OF THESE ADDRESSES OR TO THE PLACE OF  
PURCHASE.  
setting that you desire press the Temp Down button  
.
TIMER: To activate the timer from the remote control, press  
the button marked Timer. From there you can press the  
Temp Up or Temp Down button , which will give you  
the ability to program the heater to turn on or off in 1 hour  
increments, up to 16 hours. For more information see the  
programmable timer instructions above.  
What are the limits on JCS’s Liability?  
JCS shall not be liable for any incidental or consequential  
damages caused by the breach of any express, implied or  
statutory warranty or condition.  
Except to the extent prohibited by applicable law, any  
implied warranty or condition of merchantability or fitness  
for a particular purpose is limited in duration to the  
duration of the above warranty.  
For your convenience a remote control holder is integrated  
into the heater.  
Please DO NOT attempt to open or repair the heater.  
Please see the Warranty for Service Instructions.  
If you have any questions regarding your product or  
would like to learn more about other Bionaire® products,  
please contact our Consumer Service Department at  
1-800-253-2764 or visit our website at  
JCS disclaims all other warranties, conditions or  
representations, express, implied, statutory or otherwise.  
JCS shall not be liable for any damages of any kind  
resulting from the purchase, use or misuse of, or inability to  
use the product including incidental, special,  
consequential or similar damages or loss of profits, or for  
any breach of contract, fundamental or otherwise, or for  
any claim brought against purchaser by any other party.  
Some provinces, states or jurisdictions do not allow the  
exclusion or limitation of incidental or consequential  
damages or limitations on how long an implied warranty  
lasts, so the above limitations or exclusion may not apply  
to you.  
© 2008 Sunbeam Products, Inc. doing business as Jarden  
Consumer Solutions. All rights reserved. Distributed by  
Sunbeam Products, Inc. doing business as Jarden  
Consumer Solutions, Boca Raton, Florida 33431.  
Printed in China  
 

Belkin Network Router F9K1003 User Manual
Binatone GPS Receiver B350 User Manual
Black Decker Trimmer 90518528 User Manual
Boss Audio Systems MP3 Player MR1305WUA User Manual
Briggs Stratton Portable Generator 040220A User Manual
Bushnell Binoculars 26 0224 User Manual
Cable Electronics Stereo Amplifier AV400 User Manual
Canon Fax Machine FAX L295 L290 User Manual
Casio Projector XJ H1700 User Manual
Cecilware Coffeemaker JAVA2 LP User Manual